# Phono vs Line Level Explained: Why Your Turntable Needs the Right Input

Source: https://turntablenest.com/blog/phono-vs-line-level-explained
Published: 2026-11-20
Publisher: Turntable Nest

You flip a turntable around, see a tiny switch labeled phono and line and an amplifier with inputs marked phono, aux and CD, and the question is which to use. These labels describe two different strengths of audio signal, and connecting them wrongly gives sound that is faint and dull or loud and harsh. This guide explains the difference, why records need extra processing and how to match the output of your turntable to the input on your system.

## Two kinds of signal

Line level is the standard signal used by components such as CD players, streamers and tuners. It is strong enough to go straight into an amplifier input like aux or CD. Phono level is the much weaker signal that comes directly from a turntable cartridge, and it needs to be boosted before it reaches the same stage.

Besides being weaker, the phono signal is shaped on purpose. Records are cut with bass reduced and treble boosted, so a phono stage reverses that to restore a natural balance. This is why plugging a bare turntable into a line input sounds thin, quiet and tinny.

## What a phono stage does

A phono stage, also called a phono preamp, does two jobs. It raises the level of the tiny cartridge signal, and it applies the equalization curve that undoes the shaping done when the record was cut. The result is a line level signal that any normal input can accept.

Phono stages exist in several places. Some amplifiers and receivers include one and label the input phono. Some turntables include one inside the plinth. Others rely on a separate small box that sits between the turntable and the amplifier, and you will find those in our phono preamp guide.

[See phono preamp picks](https://turntablenest.com/best/phono-preamps)

## How to tell what your turntable outputs

Look at the back of the turntable for a switch labeled phono and line or mic and line. If there is one, it controls whether the built-in preamp is active. Line means the preamp is on and the signal is line level, and phono means the preamp is bypassed and the signal is phono level.

If there is no switch, check the manual or the specification page from the manufacturer. A turntable with no built-in preamp outputs phono level only. A turntable with a fixed built-in preamp outputs line level only, and some models offer a switch, so read the specification for your exact model.

## Matching the output to the input

The rule is simple: phono output goes to a phono input or a phono preamp, and line output goes to a line input such as aux. If your amplifier has a phono input, set the turntable to phono output, if it has that option, and connect it there.

If your amplifier has no phono input, either use a turntable with a built-in preamp set to line or add an external phono preamp. Using a built-in preamp and an amplifier phono input together is not recommended, because the signal is boosted twice and can sound loud and distorted.

[Check whether you need a phono preamp](https://turntablenest.com/blog/do-you-need-a-phono-preamp)

## What happens if you connect it wrong

Phono into line gives low volume and a thin sound with weak bass. Line into phono gives an overly loud, distorted and harsh signal. Neither is likely to damage modern equipment at normal volumes, but you should turn the volume down before testing and raise it slowly.

If the sound seems wrong, stop and check both ends. Confirm the switch position, the input you have selected on the amplifier and that the ground wire is connected where a ground terminal exists. Small mistakes here are the most common reason new setups sound disappointing.

## Where the term aux fits in

Aux, CD, tuner and similar labels on an amplifier all describe line level inputs. They are not meant for a bare turntable, even though the plugs look identical. The jacks are the same RCA type, so it is easy to plug into the wrong pair without noticing until you hear the result.

If your amplifier is older and has a dedicated phono input, it will usually be labeled clearly and often sits at the end of the row. Newer amplifiers sometimes leave the input out entirely to save space and cost, which is why a separate phono stage or a turntable with a built-in one has become common.

When in doubt, look up the manual for the amplifier and search for phono, MM or turntable. The input list will tell you which jack is intended for a record player, and whether it supports moving magnet only or both types of cartridge.

## MM and MC cartridges and gain

Phono stages are also designed for a type of cartridge. Moving magnet cartridges are common and have a stronger output, while moving coil cartridges usually have a lower output and need more gain. Some phono stages offer a switch for MM or MC, while simpler ones support only moving magnet.

If you plan to upgrade your cartridge later, check that your phono stage can handle the type you choose. Look at the cartridge output voltage and the stage gain in the manufacturer's data to make sure they are compatible.

[Read moving magnet vs moving coil](https://turntablenest.com/blog/moving-magnet-vs-moving-coil-cartridges)

## A quick checklist before you connect

Power everything off and turn the volume down. Identify whether the turntable has a built-in preamp, then choose the matching input on the amplifier. Connect the cables, attach the ground wire if there is one and power on, bringing the volume up slowly while the record plays.

If you still hear hum, check the grounding and the position of cables near power supplies. If sound is faint, recheck the phono and line setting. A careful pass through these steps solves most beginner connection problems without buying anything new.

[Read how to ground a turntable](https://turntablenest.com/blog/how-to-ground-a-turntable)

## Related buying guides

- https://turntablenest.com/best/phono-preamps
- https://turntablenest.com/best/stereo-receivers
- https://turntablenest.com/best/integrated-amplifiers
- https://turntablenest.com/best/turntable-ground-wires
