# RCA Cables for Turntables: What They Do, What to Look For and How to Connect Them

Source: https://turntablenest.com/blog/rca-cables-for-turntables
Published: 2026-11-21
Publisher: Turntable Nest

Most turntables send their signal to an amplifier through a pair of RCA plugs, one red for the right channel and one white or black for the left. It sounds simple until the cable that came with your deck is too short, the plugs do not seem to fit or you hear hum after connecting it. This guide explains what the cables do, how to choose a length and style, how to connect them and how much cable quality really matters.

## What RCA cables do on a turntable

A turntable cartridge produces a tiny signal. The RCA cable carries it, one channel per plug, from the turntable to a phono input on an amplifier, receiver or a separate phono preamp. Because the signal is so small, any interference picked up along the way is amplified later, which is why the cable and the connections matter.

Red goes to the right channel and white goes to the left. Some cables use black instead of white for the left channel. Keeping the colors matched on both ends is important, because a swapped pair puts the left and right channels on the wrong sides of the stereo image.

## Fixed cable or removable cable

Some turntables have a cable permanently attached at the tonearm base, while others have RCA sockets on the back of the plinth and use a removable cable. A removable cable is easier to replace if it becomes damaged or if you want a different length. A fixed cable cannot be changed without modifying the unit, so check which you have before shopping.

If your turntable has a built-in cable, you do not need to buy one to get started. Look at the back or underside of the plinth to see the output. Many turntables also have a ground wire that is separate from the RCA plugs, and it should be connected to the ground terminal on the amplifier or preamp when one is provided.

[Read how to ground a turntable](https://turntablenest.com/blog/how-to-ground-a-turntable)

## Choosing length and connectors

Pick a length that reaches comfortably without a tight bend or a long loop of excess cable. Too much slack lets the cable pick up more noise and can tangle with power cords. Keep signal cables away from power cables where possible, and if they must cross, cross them at right angles.

Think about where the turntable and amplifier will sit. If they are on separate shelves or the amplifier is across the room, a longer cable may be needed, but a very long run of low level phono signal is more exposed to interference. Moving the equipment closer together is often better than buying a longer cable.

Check the plugs fit your sockets snugly. Plugs that are loose can cause crackle or dropouts. Metal plugs that grip well and a cable with decent shielding are practical features, and they matter more than fancy marketing language. Gold plated plugs are common, and the plating mostly helps resist corrosion.

## Does a more expensive cable sound better

Opinions differ here, and we cannot promise audible gains from any cable. What is generally agreed is that a well built, shielded cable with solid connectors does the job reliably, while a poorly shielded or damaged one can add hum or noise. Beyond that point, improvements are subtle and depend on the rest of the system.

If you are hearing hum, check the ground connection, the cable routing and the phono input setting before spending on a new cable. The cause is more often a grounding or placement problem than the cable itself. Fix the basics first and upgrade later if you want to experiment.

[See cable upgrade picks](https://turntablenest.com/best/cable-upgrades)

## Connecting the cable step by step

Turn the amplifier off and lower the volume. Plug the red connector into the red or right input and the white or black connector into the matching left input on the phono input, not the aux input, unless your turntable has a built-in preamp. Then connect the ground wire to the ground screw if the amplifier has one.

If your amplifier has no phono input, you need a phono preamp between the turntable and a line input. Some turntables have a switch to select phono or line output, and it must match what you connect to. Using the wrong setting can make the sound weak and thin or very loud and distorted.

[Check whether you need a phono preamp](https://turntablenest.com/blog/do-you-need-a-phono-preamp)

## Common cable problems

Hum or buzz often points to a missing ground or a cable running beside a power adapter. Crackle can come from a loose plug or a dirty contact. Sound from one speaker only can be a cable fault, a loose connector or a balance setting, and the cable is easy to test by swapping it with another.

Intermittent sound that changes when you touch the cable usually means a damaged connector or a broken conductor inside the cable. Replace it rather than trying to bend it into position. If you have a spare cable, swap it in to confirm the diagnosis before you buy a new component.

[Troubleshoot sound from only one channel](https://turntablenest.com/blog/turntable-sound-only-one-channel)

## Adapters and other connection types

Some modern turntables offer USB output or Bluetooth in addition to RCA. These routes can be convenient, but they do not replace the RCA output for connecting to a hi-fi system. If you use an adapter, such as RCA to 3.5 mm, make sure the turntable output is line level or that a preamp is in the chain.

Plugging a phono level signal into a line input without a preamp usually produces very quiet and dull sound. This is not a cable fault. Check your turntable specifications to see whether it has a built-in preamp, and match the input type on the amplifier.

## Related buying guides

- https://turntablenest.com/best/cable-upgrades
- https://turntablenest.com/best/phono-preamps
- https://turntablenest.com/best/turntable-ground-wires
- https://turntablenest.com/best/stereo-receivers
