How to Digitize Vinyl Records: Connect a Turntable to a Computer and Save Your Music
Published How we research
Maybe you want to carry an old record on your phone, back up something that is hard to replace or just hear a favorite album while you cook. Digitizing vinyl means playing a record and recording the sound as a file. It is not complicated, but the connection and levels have to be right or the result sounds thin or distorted. This guide covers the main routes, what you need, how to record and check the result.
Products from this article
The highest-scoring picks from the buying guides this article links to. Scores are our editorial assessment, not customer ratings.
As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.
+ Direct drive with 3 speeds covers LPs, singles and older shellac pressings
From our guide: Best USB Turntables (2026)
+ Switchable MM and MC modes cover most turntable cartridges.
From our guide: Best Phono Preamps (2026)
+ Dense carbon fibers sweep dust from deep in the grooves
From our guide: Best Anti-Static Brushes for Vinyl (2026)
+ Two-step process tackles grime then leaves an anti-static finish
From our guide: Best Record Cleaning Solutions for Vinyl (2026)

Check what you are allowed to do
Copying your own records for personal listening is common, but copyright rules differ by country and by use. Making copies to share or sell is a different matter. If you are unsure about the rules where you live, check local guidance before you start, and keep the files for personal use.
It also helps to think about why you are digitizing. If the aim is to listen on the go, a decent quality file is enough. If the aim is to preserve a rare record, plan for a careful setup, clean records and a higher quality format.
Route one: a USB turntable
The simplest route is a turntable with a built-in USB output. It connects to your computer with a USB cable, and the computer sees it as an audio input. Many of these models include a built-in preamp, and some come with software or a recommended app, so check the manual.
USB turntables are convenient, but the built-in electronics and cartridge vary in quality. They are a practical way to get started with a small number of records. Our USB turntable guide compares models by features so you can see what each one includes.
Route two: your existing turntable and an interface
If you already own a turntable, you can connect it to a phono preamp and then to an audio interface or a USB adapter with line inputs. The preamp raises and equalizes the phono signal, and the interface turns the analog signal into digital audio that the computer can record.
Some phono preamps include a USB output, which saves a box. Make sure the stage matches your cartridge type and that you connect the ground wire if the preamp has a terminal. If you hear hum in the recording, check grounding and cable routing first.
Software and settings
Any audio recording program can capture the sound. Free options exist for most computers, and many people use a program that lets them see the waveform, trim the start and end and split the record into tracks. Choose your input device in the program settings and make a short test recording.
Pick a format and quality that suits your goal. An uncompressed file keeps the most detail but takes more storage, while compressed formats are smaller and fine for everyday listening. A common approach is to record in an uncompressed format and make compressed copies for your phone.
Set the recording level
Play the loudest part of the record and watch the level meter. You want the peaks to come close to the top without hitting it, because hitting the top causes distortion that cannot be fixed later. If the meter is very low, raise the input level, and if it hits the top, lower it.
Leave a little headroom, since an unexpected loud passage can appear on the other side of the record. It is better to record slightly low and raise the volume later than to record too loud and clip.
Test the chain before the real recording
Make a short test with a record you do not mind replaying. Listen on headphones and check that both channels are present, that there is no hum when the stylus is lifted and that the sound is neither thin nor harsh. A thin sound often means a phono signal went into a line input.
Fix any problems before you record a whole collection. A mistake in the chain, such as the wrong input or a missing ground, will repeat on every file, and finding it after many hours of recording is frustrating.
Prepare the record and stylus
A clean record gives a cleaner recording, because dust and static become clicks and pops in the file. Use a soft brush before each side and consider a proper cleaning for dirty records. Check that the stylus is clean and in good condition, because a worn stylus can add distortion that stays in the recording.
Place the turntable on a stable surface and avoid walking heavily or bumping the table during recording. Vibration and footfalls show up in the file and are hard to remove afterwards.
Fixing clicks, pops and hum afterwards
Many audio programs offer click removal and noise reduction tools. They can lessen small clicks and background hum, but they also change the sound if used heavily, so apply them lightly and compare with the original. Keep an untouched copy of the raw recording so you can start over.
Some people prefer to leave the natural surface noise in place as part of the vinyl sound, and others like a cleaner file. Neither is wrong, so choose what you enjoy. Repairs work best on short, isolated clicks and less well on constant crackle from a worn record.
Record, edit and save
Record a full side in one go, then stop. Trim the silence at the start and end and split the side into tracks. Name the files with the artist, album and track number so they sort properly in your music player, and fill in the tags if your software supports them.
Listen through the file before moving on to the next record. If you hear problems such as hum, clicks or distortion, fix the cause and record again rather than relying on heavy repairs. Back up your files to a second drive once you are happy with them.
Popular right now
- How to Ground a Turntable and Eliminate HumArticle
- How to Align a Phono Cartridge for Accurate TrackingArticle
- RIAA equalization explainedGlossary
- Setting Tracking ForceArticle
- Best Stylus Cleaners for Vinyl (2026)Buying guide
- How to Fix a Turntable Playing Through Only One ChannelArticle
Based on the last 28 days of search and visitor data.