Independent buying guides for vinyl and turntables

Parts of a Turntable: Every Component Named and Explained

Published Updated How we research

A turntable looks simple, but it is a small machine with a dozen named parts, and knowing them makes setup, cleaning and troubleshooting much easier. The platter spins the record, the tonearm carries the cartridge across it, and the stylus at the tip of the cartridge reads the groove. Around those three sit the motor, the drive system, the counterweight, the controls and the cables that send the signal onward. This guide names every main part in the order you meet it, explains what it does, and points out which ones you can adjust or replace yourself.

Products from this article

The highest-scoring picks from the buying guides this article links to. Scores are our editorial assessment, not customer ratings.

As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.

Artistic black and white close-up of a vinyl record on a turntable, emphasizing music nostalgia
Photo: Bob Clark on Pexels

The plinth, feet and dust cover

The plinth, sometimes called the base or chassis, is the body that holds everything else. Its job is to give the motor, platter and tonearm a stable mounting point and to resist vibration. Plinths are made from materials such as MDF, plastic, wood or metal, and heavier, stiffer designs generally pick up less unwanted vibration from the room, though that is a tendency rather than a rule.

Under the plinth you will find the feet, which set the height and help absorb vibration. Some are fixed and some can be adjusted to level the deck. The hinged dust cover keeps dust off the record and stylus while you play or store the turntable. Many people lift it off or leave it open during playback because some covers can rattle, so check how yours behaves with the music on.

Platter, mat and spindle

The platter is the round disc that the record sits on. It turns at a steady speed, usually 33 1/3 or 45 revolutions per minute, with 78 on some models. A heavier platter tends to hold its speed more steadily because it has more inertia, while lighter platters are common on entry-level decks. Platters are commonly made of metal, glass, acrylic or plastic.

On top of the platter sits the mat, a thin disc of rubber, felt, cork or similar material that supports the record and absorbs a little vibration. The spindle is the short center pin that passes through the hole in the record to keep it centered. Handle the spindle gently, and never force a record onto it. A 45 RPM single with a large center hole needs an adapter to fit the spindle.

The motor and the drive system

The motor creates the rotation that turns the platter, but how that rotation reaches the platter depends on the drive type. In a belt-drive turntable, a thin rubber belt loops around the motor pulley and the platter or a sub-platter. The belt acts as a small cushion between the motor and the platter, which helps keep motor noise away from the stylus. The belt is also a wear item that can stretch over the years.

In a direct-drive turntable the platter sits right on the motor, so there is no belt to replace and the platter reaches speed quickly. That is one reason direct-drive decks are popular with DJs. An idler-wheel design, found on some vintage decks, uses a small rubber wheel to couple the motor to the platter. Each system can sound and work well when it is built carefully. The practical difference is mostly in maintenance, start-up time and how much motor vibration the maker has to manage.

Tonearm, headshell and counterweight

The tonearm is the pivoting arm that holds the cartridge and lets it travel across the record from the outer edge to the label. It must move freely yet hold the cartridge steady. On many decks the cartridge is attached to a removable headshell, a small mount at the end of the arm that carries the cartridge and makes swapping easier. Other decks have a fixed headshell built into the arm.

The counterweight sits on the rear of the tonearm and balances it so the stylus is not pressing down too hard or too lightly. Turning it sets the tracking force, which is how many grams of downward pressure the stylus applies to the groove. Most arms also have an anti-skate control, which compensates for the inward pull on the stylus as the record spins. Both settings should follow the cartridge maker's recommendation. A small dial or sliding weight is typical for anti-skate.

See headshell picks →

Cartridge and stylus

The cartridge is the small unit at the end of the tonearm that turns groove movement into a tiny electrical signal. Inside it, magnets and coils generate that signal. The two common designs are moving magnet and moving coil, and each needs a matching input on the amplifier or phono preamp. Cartridges are fastened with two small screws, and their position affects how accurately the stylus tracks the groove.

The stylus is the tip that actually touches the groove. People often call it the needle, and the two words are used interchangeably in everyday speech. The stylus is mounted on a thin rod called the cantilever. The stylus is the part that wears with use, and many makers suggest replacing it after a few hundred to roughly a thousand hours of play, depending on the stylus shape and how clean the records are. Check your cartridge's documentation for its own guidance.

See replacement stylus picks →

Controls, cables and the ground wire

Most turntables have a speed selector for 33 and 45 RPM, a start and stop control, and a cueing lever that lifts and lowers the tonearm gently. The lever is a handy safeguard because it lets you place the stylus on the record without a shaky hand. Some models add automatic arm return, a pitch control for adjusting speed, or a built-in phono preamp with a small line and phono switch on the back.

On the back you will find the output cables, usually a pair of RCA plugs for left and right channels. A separate thin wire with a small spade end is the ground wire, and it connects to the grounding post on an amplifier or preamp. If it is missing or loose you may hear a low hum. Always unplug the deck before touching internal parts, and keep your fingers away from the stylus tip, which is delicate and easy to damage.

See ground wire picks →

The Tonearm in Detail

The tonearm carries the cartridge and sets how the stylus tracks the groove. This page covers its parts, the main arm types and what each does for playback.

Learn about tonearms →

Popular right now

  1. How to Ground a Turntable and Eliminate HumArticle
  2. How to Align a Phono Cartridge for Accurate TrackingArticle
  3. RIAA equalization explainedGlossary
  4. Setting Tracking ForceArticle
  5. Best Stylus Cleaners for Vinyl (2026)Buying guide
  6. How to Fix a Turntable Playing Through Only One ChannelArticle

Based on the last 28 days of search and visitor data.