Independent buying guides for vinyl and turntables

What Is a Tonearm and What Does It Do on a Turntable?

Published Updated How we research

The tonearm is the long pivoting arm on a turntable that carries the cartridge and stylus across the record. It has to do three things at once: hold the cartridge steady, let it follow the spiral groove with almost no resistance, and apply just the right amount of downward pressure. A well-designed arm is a quiet part of a good sound, and a poor one is a common cause of skipping, distortion and uneven wear. This article explains how a tonearm works, the main types, the adjustments it offers, and what to look for when comparing turntables.

Products from this article

The highest-scoring picks from the buying guides this article links to. Scores are our editorial assessment, not customer ratings.

As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.

Blurry spinning vinyl record with needle on turntable, capturing the essence of analog music
Photo: Miguel Cuenca on Pexels

What a tonearm actually does

The tonearm holds the cartridge at the correct angle above the record and lets it travel from the outer edge toward the label as the groove spirals inward. The arm pivots at a bearing near its base, which allows it to swing sideways with the groove, and often also lets it move up and down to follow small warps in the record.

That is a demanding job, since the stylus is following a groove that is only a fraction of a millimeter wide. The arm should move freely enough that the stylus is not dragged along, yet be rigid enough that it does not flex or resonate. Designers balance those goals using different shapes, materials and bearing types, which is why tonearms vary widely between turntables.

The main parts of a tonearm

Working from the front, a typical arm has a headshell that carries the cartridge, an arm tube, a pivot bearing, and at the back a counterweight. Some arms have a removable headshell, some have a fixed one, and some have a single piece that combines the headshell and the arm tube. Wires inside the tube carry the signal from the cartridge to the output cables.

Most arms also have a cueing lever, which lifts and lowers the arm slowly, an arm rest or clip that holds the arm when not in use, and often a height adjustment at the pivot. The cueing lever protects both the record and the stylus, because it avoids dropping the stylus onto the record. Keep it in use, even on decks where you could do it by hand.

Inside the arm, the pivot is usually the most important part. Bearings may be gimbal types with tiny points, unipivot designs with a single point, or simple sleeve arrangements on basic decks. Better bearings move with less friction in both directions. You do not need to understand the design to enjoy a record, but if the arm sticks, wobbles or has noticeable play when you gently wiggle it, the sound and record wear can suffer.

See headshell picks →

Straight and curved arms

Tonearms come in two common shapes. A straight arm has a simple line from pivot to headshell and is common on DJ-style turntables, where the arm is built to be robust and cope with rough handling. An S-shaped or curved arm has a bend that is part of the geometry intended to keep the stylus close to the right angle across the record.

Because the arm swings in an arc, the stylus cannot be at a perfect angle at every point on the record. Designers choose the geometry to keep the error small across the playing surface, and cartridge alignment tools help set the cartridge in the headshell so the error is shared well. Neither shape is automatically better. The quality of the bearing, the stiffness and the setup matter more.

See cartridge alignment tools →

Tracking force and the counterweight

Tracking force is how much downward pressure the stylus puts on the groove, measured in grams. The counterweight on the rear of the arm sets it. You first balance the arm so it floats level with zero force, then turn the counterweight or its scale to the value the cartridge maker recommends. A stylus gauge is a good way to check the result.

If the force is too light, the stylus can skip or mistrack, and if it is too heavy, it can add wear to both the stylus and the groove. For that reason, follow the maker's range and avoid guessing. Some turntables have preset arms where the counterweight is fixed or adjusted at the factory, and in that case you should leave it unless the manual says otherwise.

See stylus force gauge picks →

Anti-skate and arm height

Because of the arm geometry and the friction of the spinning record, the stylus feels a small sideways pull toward the center of the record. Anti-skate is a control that applies a small opposing force to counter that pull. A common starting point is to set it close to the tracking force value, then fine-tune by ear or according to the cartridge maker's advice.

Arm height, sometimes called vertical tracking angle or VTA, affects how the stylus sits in the groove. Many entry-level arms are not adjustable, and that is fine. On arms that are adjustable, small changes can alter the tonal balance, so make changes in small steps and only after the tracking force is correctly set. Do not worry about fine height tuning on a basic deck.

What to look for in a tonearm

A good tonearm moves smoothly with no sticking or side play at the bearing, holds its settings and feels solid when you handle it. Check that the headshell connection is secure, that the cueing lever lowers the arm slowly, and that the counterweight turns firmly. Replaceable headshells and standard cartridge mounting let you upgrade later.

On a budget, a fixed arm with a pre-mounted cartridge is perfectly reasonable, as long as it tracks cleanly. Handle every arm gently, lock it before moving the turntable, and keep your fingers off the stylus. If you notice skipping, buzzing or an arm that drifts, it is worth checking the setup before blaming the cartridge.

When buying, remember that a tonearm and cartridge work as a pair. A cartridge that is very heavy or very light for the arm can be hard to balance, and the arm's effective mass affects how it works with the cartridge's suspension. The turntable maker or cartridge maker will often give guidance on compatible pairings, so check before mixing parts.

Where the tonearm fits in the whole deck

Once you understand the tonearm, it helps to see how it works with the rest of the deck, since the arm depends on a stable plinth, a steady platter and a good drive system. This guide names each part of a turntable, from feet and dust cover to platter, mat, spindle and motor, and explains what each does.

Parts of a turntable explained →

Popular right now

  1. How to Ground a Turntable and Eliminate HumArticle
  2. How to Align a Phono Cartridge for Accurate TrackingArticle
  3. RIAA equalization explainedGlossary
  4. Setting Tracking ForceArticle
  5. Best Stylus Cleaners for Vinyl (2026)Buying guide
  6. How to Fix a Turntable Playing Through Only One ChannelArticle

Based on the last 28 days of search and visitor data.